Charging and discharging FET are ON but output voltage(pack Output) is zero, how it can be recover from this. and what commands can be used .
[Header]
bq EVSW Version = 0.9.52
DeviceName = bq20z95 v1.50
Time = 5/21/2015 9:57:18 PM
[Voltage(1st Level Safety)]
COV Threshold = 4300
COV Time = 2
COV Recovery = 4100
COV Delta = 20
COV Temp. Hys = 10.0
POV Threshold = 17500
POV Time = 2
POV Recovery = 16000
CUV Threshold = 2500
CUV Time = 2
CUV Recovery = 3000
PUV Threshold = 11000
PUV Time = 2
PUV Recovery = 12000
[Current(1st Level Safety)]
OC (1st Tier) Chg = 6000
OC (1st Tier) Chg Time = 2
OC Chg Recovery = 200
OC (1st Tier) Dsg = 20000
OC (1st Tier) Dsg Time = 2
OC Dsg Recovery = 200
OC (2nd Tier) Chg = 7000
OC (2nd Tier) Chg Time = 2
OC (2nd Tier) Dsg = 22000
OC (2nd Tier) Dsg Time = 2
Current Recovery Time = 10
AFE OC Dsg = 1F
AFE OC Dsg Time = 0F
AFE OC Dsg Recovery = 5
AFE SC Chg Cfg = 14
AFE SC Dsg Cfg = 44
AFE SC Recovery = 1
[Temperature(1st Level Safety)]
Over Temp Chg = 55.0
OT Chg Time = 2
OT Chg Recovery = 50.0
Over Temp Dsg = 60.0
OT Dsg Time = 2
OT Dsg Recovery = 55.0
[Host Comm(1st Level Safety)]
Host Watchdog Timeout = 0
[Voltage(2nd Level Safety)]
SOV Threshold = 18000
SOV Time = 0
Cell Imbalance Current = 5
Cell Imbalance Fail Voltage = 1000
Cell Imbalance Time = 0
Battery Rest Time = 1800
Min CIM-check voltage = 3000
PFIN Detect Time = 0
[Current(2nd Level Safety)]
SOC Chg = 8000
SOC Chg Time = 0
SOC Dsg = 10000
SOC Dsg Time = 0
[Temperature(2nd Level Safety)]
SOT Chg = 65.0
SOT Chg Time = 0
SOT Dsg = 75.0
SOT Dsg Time = 0
Open Thermistor = -33.3
Open Time = 0
[FET Verification(2nd Level Safety)]
FET Fail Limit = 20
FET Fail Time = 0
[AFE Verification(2nd Level Safety)]
AFE Check Time = 0
AFE Fail Limit = 10
AFE Fail Recovery Time = 20
AFE Init Retry Limit = 6
AFE Init Limit = 20
[Fuse Verification(2nd Level Safety)]
Fuse Fail Limit = 2
Fuse Fail Time = 0
[Charge Inhibit Cfg(Charge Control)]
Chg Inhibit Temp Low = -10.0
Chg Inhibit Temp High = 45.0
Temp Hys = 1.0
[Pre-Charge Cfg(Charge Control)]
Pre-chg Current = 250
Pre-chg Temp = 12.0
Pre-chg Voltage = 3000
Recovery Voltage = 3100
[Fast Charge Cfg(Charge Control)]
Fast Charge Current = 3000
Charging Voltage = 16800
Delta Temp = 5.0
Suspend Low Temp = -10.0
Suspend High Temp = 55.0
[Pulse Charge Cfg(Charge Control)]
Turn ON Voltage = 4150
Turn OFF Voltage = 4250
Max ON Pulse Time = 60.00
Min OFF Pulse Time = 0.00
Max OFF Voltage = 4270
[Termination Cfg.(Charge Control)]
Maintenance Current = 0
Taper Current = 250
Taper Voltage = 300
Current Taper Window = 40
TCA Set % = -1
TCA Clear % = 95
FC Set % = -1
FC Clear % = 98
[Cell Balancing Cfg(Charge Control)]
Min Cell Deviation = 1750
[Charging Faults(Charge Control)]
Over Charging Voltage = 500
Over Charging Volt Time = 2
Over Charging Current = 500
Over Charging Curr Time = 2
Over Charging Curr Recov = 100
Depleted Voltage = 8000
Depleted Voltage Time = 2
Depleted Recovery = 8500
Over Charge Capacity = 300
Over Charge Recovery = 2
FC-MTO = 10800
PC-MTO = 3600
Charge Fault Cfg = 00
[Data(SBS Configuration)]
Rem Cap Alarm = 400
Rem Energy Alarm = 10000
Rem Time Alarm = 10
Init Battery Mode = 0081
Design Voltage = 14400
Spec Info = 0031
Manuf Date = 20-May-2014
Ser. Num. = 0001
Cycle Count = 0
CC Threshold = 10800
CC % = 90
CF MaxError Limit = 100
Design Capacity = 12000
Design Energy = 172800
Manuf Name = SmarTEC
Device Name = SmarTEC
Device Chemistry = LION
[Configuration(SBS Configuration)]
TDA Set % = 6
TDA Clear % = 8
FD Set % = 2
FD Clear % = 5
TDA Set Volt Threshold = 5000
TDA Set Volt Time = 5
TDA Clear Volt = 5500
FD Set Volt Threshold = 5000
FD Volt Time = 5
FD Clear Volt = 5500
[Manufacturer Data(System Data)]
Pack Lot Code = 0001
PCB Lot Code = 0001
Firmware Version = A41B
Hardware Revision = 0001
Cell Revision = 0001
[Manufacturer Info(System Data)]
Manuf. Info = 20z95
[Lifetime Data(System Data)]
Lifetime Max Temp = 41.2
Lifetime Min Temp = 13.8
Lifetime Max Cell Voltage = 6459
Lifetime Min Cell Voltage = 0
Lifetime Max Pack Voltage = 16492
Lifetime Min Pack Voltage = 6491
Lifetime Max Chg Current = 4779
Lifetime Max Dsg Current = -6183
Lifetime Max Chg Power = 65480
Lifetime Max Dsg Power = -66100
Life Max AvgDsg Cur = -2000
Life Max AvgDsg Pow = -3022
Lifetime Avg Temp = 23.7
[Lifetime Temp Samples(System Data)]
LT Temp Samples = 34
[Registers(Configuration)]
Operation Cfg A = 2F29
Operation Cfg B = 6C48
Operation Cfg C = 0000
Permanent Fail Cfg = 0000
Non-Removable Cfg = 0000
[LED Cfg(LED Support)]
LED Flash Rate = 2.000
LED Blink Rate = 1.000
LED Delay = 48.8
LED Hold Time = 2
CHG Flash Alarm = 10
CHG Thresh 1 = 0
CHG Thresh 2 = 20
CHG Thresh 3 = 40
CHG Thresh 4 = 60
CHG Thresh 5 = 80
DSG Flash Alarm = 10
DSG Thresh 1 = 0
DSG Thresh 2 = 20
DSG Thresh 3 = 40
DSG Thresh 4 = 60
DSG Thresh 5 = 80
Sink Current = 3
[Power(Power)]
Flash Update OK Voltage = 7500
Shutdown Voltage = 7000
Shutdown Time = 10
Cell Shutdown Voltage = 1750
Cell Shutdown Time = 10
Charger Present = 3000
Sleep Current = 10
Bus Low Time = 5
Cal Inhibit Temp Low = 5.0
Cal Inhibit Temp High = 45.0
Sleep Voltage Time = 5
Sleep Current Time = 20
Wake Current Reg = 00
[IT Cfg(Gas Gauging)]
Load Select = 3
Load Mode = 0
Term Voltage = 12000
User Rate-mA = 0
User Rate-mW = 0
Reserve Cap-mAh = 0
Reserve Cap-mWh = 0
[Current Thresholds(Gas Gauging)]
Dsg Current Threshold = 100
Chg Current Threshold = 50
Quit Current = 10
Dsg Relax Time = 1
Chg Relax Time = 60
[State(Gas Gauging)]
Qmax Cell 0 = 12000
Qmax Cell 1 = 12000
Qmax Cell 2 = 12000
Qmax Cell 3 = 12000
Qmax Pack = 12000
Update Status = 06
Avg I Last Run = -2000
Avg P Last Run = -3022
Delta Voltage = 0
[R_a0(Ra Table)]
Cell0 R_a flag = FF55
Cell0 R_a 0 = 160
Cell0 R_a 1 = 166
Cell0 R_a 2 = 153
Cell0 R_a 3 = 151
Cell0 R_a 4 = 145
Cell0 R_a 5 = 152
Cell0 R_a 6 = 176
Cell0 R_a 7 = 204
Cell0 R_a 8 = 222
Cell0 R_a 9 = 254
Cell0 R_a 10 = 315
Cell0 R_a 11 = 437
Cell0 R_a 12 = 651
Cell0 R_a 13 = 1001
Cell0 R_a 14 = 1458
[R_a1(Ra Table)]
Cell1 R_a flag = FF55
Cell1 R_a 0 = 160
Cell1 R_a 1 = 166
Cell1 R_a 2 = 153
Cell1 R_a 3 = 151
Cell1 R_a 4 = 145
Cell1 R_a 5 = 152
Cell1 R_a 6 = 176
Cell1 R_a 7 = 204
Cell1 R_a 8 = 222
Cell1 R_a 9 = 254
Cell1 R_a 10 = 315
Cell1 R_a 11 = 437
Cell1 R_a 12 = 651
Cell1 R_a 13 = 1001
Cell1 R_a 14 = 1458
[R_a2(Ra Table)]
Cell2 R_a flag = FF55
Cell2 R_a 0 = 160
Cell2 R_a 1 = 166
Cell2 R_a 2 = 153
Cell2 R_a 3 = 151
Cell2 R_a 4 = 145
Cell2 R_a 5 = 152
Cell2 R_a 6 = 176
Cell2 R_a 7 = 204
Cell2 R_a 8 = 222
Cell2 R_a 9 = 254
Cell2 R_a 10 = 315
Cell2 R_a 11 = 437
Cell2 R_a 12 = 651
Cell2 R_a 13 = 1001
Cell2 R_a 14 = 1458
[R_a3(Ra Table)]
Cell3 R_a flag = FF55
Cell3 R_a 0 = 160
Cell3 R_a 1 = 166
Cell3 R_a 2 = 153
Cell3 R_a 3 = 151
Cell3 R_a 4 = 145
Cell3 R_a 5 = 152
Cell3 R_a 6 = 176
Cell3 R_a 7 = 204
Cell3 R_a 8 = 222
Cell3 R_a 9 = 254
Cell3 R_a 10 = 315
Cell3 R_a 11 = 437
Cell3 R_a 12 = 651
Cell3 R_a 13 = 1001
Cell3 R_a 14 = 1458
[R_a0x(Ra Table)]
xCell0 R_a flag = FFFF
xCell0 R_a 0 = 160
xCell0 R_a 1 = 166
xCell0 R_a 2 = 153
xCell0 R_a 3 = 151
xCell0 R_a 4 = 145
xCell0 R_a 5 = 152
xCell0 R_a 6 = 176
xCell0 R_a 7 = 204
xCell0 R_a 8 = 222
xCell0 R_a 9 = 254
xCell0 R_a 10 = 315
xCell0 R_a 11 = 437
xCell0 R_a 12 = 651
xCell0 R_a 13 = 1001
xCell0 R_a 14 = 1458
[R_a1x(Ra Table)]
xCell1 R_a flag = FFFF
xCell1 R_a 0 = 160
xCell1 R_a 1 = 166
xCell1 R_a 2 = 153
xCell1 R_a 3 = 151
xCell1 R_a 4 = 145
xCell1 R_a 5 = 152
xCell1 R_a 6 = 176
xCell1 R_a 7 = 204
xCell1 R_a 8 = 222
xCell1 R_a 9 = 254
xCell1 R_a 10 = 315
xCell1 R_a 11 = 437
xCell1 R_a 12 = 651
xCell1 R_a 13 = 1001
xCell1 R_a 14 = 1458
[R_a2x(Ra Table)]
xCell2 R_a flag = FFFF
xCell2 R_a 0 = 160
xCell2 R_a 1 = 166
xCell2 R_a 2 = 153
xCell2 R_a 3 = 151
xCell2 R_a 4 = 145
xCell2 R_a 5 = 152
xCell2 R_a 6 = 176
xCell2 R_a 7 = 204
xCell2 R_a 8 = 222
xCell2 R_a 9 = 254
xCell2 R_a 10 = 315
xCell2 R_a 11 = 437
xCell2 R_a 12 = 651
xCell2 R_a 13 = 1001
xCell2 R_a 14 = 1458
[R_a3x(Ra Table)]
xCell3 R_a flag = FFFF
xCell3 R_a 0 = 160
xCell3 R_a 1 = 166
xCell3 R_a 2 = 153
xCell3 R_a 3 = 151
xCell3 R_a 4 = 145
xCell3 R_a 5 = 152
xCell3 R_a 6 = 176
xCell3 R_a 7 = 204
xCell3 R_a 8 = 222
xCell3 R_a 9 = 254
xCell3 R_a 10 = 315
xCell3 R_a 11 = 437
xCell3 R_a 12 = 651
xCell3 R_a 13 = 1001
xCell3 R_a 14 = 1458
[Device Status Data(PF Status)]
PF Flags 1 = 0000
Fuse Flag = 00
PF Voltage = 14800
PF C4 Voltage = 0
PF C3 Voltage = 0
PF C2 Voltage = 0
PF C1 Voltage = 0
PF Current = 0
PF Temperature = 293.0
PF Batt Stat = 4A50
PF RC-mAh = 0
PF RC-10mWh = 0
PF Chg Status = 0000
PF Safety Status = 0000
PF Flags 2 = 0100
[AFE Regs(PF Status)]
AFE Status = 00
AFE Output = 08
AFE State = 00
AFE Function = 00
AFE Cell Select = 00
AFE OLV = 01
AFE OLT = 0F
AFE SCC = 44
AFE SCD = 44
[Data(Calibration)]
CC Gain = 10.825
CC Delta = 10.825
Ref Voltage = 1225.00
AFE Pack Gain = 672.91
CC Offset = -0.268
Board Offset = 0
Int Temp Offset = 0.0
Ext1 Temp Offset = 0.0
Ext2 Temp Offset = 0.0
[Config(Calibration)]
CC Current = 3000
Voltage Signal = 16800
Temp Signal = 298.0
CC Offset Time = 250
ADC Offset Time = 32
CC Gain Time = 250
Voltage Time = 1984
Temperature Time = 32
Cal Mode Timeout = 300
[Temp Model(Calibration)]
Ext Coef 1 = -28285
Ext Coef 2 = 20848
Ext Coef 3 = -7537
Ext Coef 4 = 401.2
Ext Min AD = 0
Ext Max Temp = 401.2
Int Coef 1 = 0
Int Coef 2 = 0
Int Coef 3 = -11136
Int Coef 4 = 575.4
Int Min AD = 0
Int Max Temp = 575.4
[Current(Calibration)]
Filter = 239
Deadband = 10
CC Deadband = 10.0