Quantcast
Channel: Power management forum - Recent Threads
Browsing all 35901 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

BQSTUDIO: Generating golden image for "Bq34z100 g1" using EV2400.

Part Number: BQSTUDIOHi Experts, I have started working on power management solution for one of our product, there I'm willing to use Bq34z100 G1.So on very first step of generating the golden image.i...

View Article


TPS65381A-Q1: WD_FAIL_CNT in DIAG when Writing WD_WIN1_CFG

Part Number: TPS65381A-Q1Hi,My customer reported when they write to WD_WIN1_CFG and WD_WIN2_CFG in DIAG, the WD_FAIL_CNT changes to 7 from 5 when it goes to ACTIVE, this forces them to make two good...

View Article


BQ27542-G1: state of charge is not come in percentage

Part Number: BQ27542-G1I use battery fuel gauge ic with i.mx6 solo dual. i use bq27xxx linux i2c driver(bq27xxx_battery.c) of ti. my ic name is bq27542.i have below confusions while writing code on...

View Article

conflict minerals statement

Dear TI Experts,Could you kindly provide a general conflict minerals statement pdf file such as attached? Thanks a lot.(Please visit the site to view this file) 

View Article

Image may be NSFW.
Clik here to view.

LM3489: LM3489 circuit suggestion for type C- PD

Part Number: LM3489Hi team,My customer is designing the PD type-c power using LM3489.They have put L30 to reduce the ripple noise at light load.They would like to consult with you whether they can...

View Article


TPS54625: Current limit accuracy of TPS54625

Part Number: TPS54625HiI have a question about TPS54625.Current limit threshold is written 7.2A(min), 8.2A(typ) and 9.5A(max) at L=1.5uH in  ELECTRICAL CHARACTERISTICS.If I change the inductor value,...

View Article

BQ27426: Fuel Gauge selecting

Part Number: BQ27426HelloDoorbell application, 5000mAh Li Battery,do you have any lowcost fuel gauge IC reccomend ?Competitor is Cellwise CW2015, its normal mode power consumption is 15uA, SLEEP MODE...

View Article

Image may be NSFW.
Clik here to view.

TPS61178: About TPS61178 En Function(Pin11)

Part Number: TPS61178Hi:I used the follow Schematic diagram, I found the En pin High or low, TPS61178 Vout  is Enable.What's the problem?Best Regards

View Article


BQ34Z100-G1: Process of Learning Cycles with Bq34z100-G1

Part Number: BQ34Z100-G1Hi Experts, I have started working for BMS in our working product, i have chosen Bq34z100-g1, I have some query regarding the same, My battery parameter is mentioned belowPlease...

View Article


UCC21710-Q1: Does a negative power supply voltage must have to be applied...

Part Number: UCC21710-Q11 Does a negative power supply voltage must have to be applied between COM and VEE?If there is no negative voltage, will the chip report fault signal?2 if there is no negative...

View Article

UCC21710-Q1: Does a negative power supply voltage must have to be applied...

Part Number: UCC21710-Q11 If there is no negative voltage, will the chip report fault signal?2 if there is no negative voltage,Internal on-chip Active Miller Clamp will not be able to use this...

View Article

UCC28061: Can UCC28061 or UCC28070 be used for circuit design to boost low DC...

Part Number: UCC28061HelloI am considering a circuit (3kW) that boosts a DC voltage of 36V to 300V.Can I use UCC28061 or UCC28070?If these cannot be used, I would like to suggest alternative ICs.Also,...

View Article

TPS65160: TPS65160 supply issue

Part Number: TPS65160We are using TPS65160 in our project for TFT display.We are not getting VGL(-5V) as per our design what may be the issue?Vcom is also getting wrong (5V instead of 3.3V)Please...

View Article


UCC28070: Low DC voltage, high power boost circuit

Part Number: UCC28070HelloI am considering a booster circuit with an input DC voltage of 36V, an output DC voltage of 300V, and 3kW.Is it possible to design with UCC28061 or UCC28070?If this is not...

View Article

Image may be NSFW.
Clik here to view.

BQ24072T: No output voltage if no battery - empty battery not charging

Part Number: BQ24072THi,I have a questions about the BQ24072T :I don't have output = Vbat + 225mV as datasheet say.Actually, with a Vout = Vbat If I only put the Vin, (no battery) Vout is approx 600mV,...

View Article


Image may be NSFW.
Clik here to view.

LM3492: Only working one of multiple prototypes

Part Number: LM3492Hi,a customer has the following issue:"We currently have a problem with a LED driver. We have several identical circuits with the attached schematic. Unfortunately only one of them...

View Article

TPS51200: Query related to the TPS51200 VTT specification

Part Number: TPS51200Hi, As per the datasheet page no 14, JEDEC VTT specifications for DDR and DDR2 (JEDEC standard: DDR JESD8-9B May 2002; DDR2 JESD8-15A Sept 2003) mentioned as...

View Article


TPS23751: Best solution for EMI/EMC considerations

Part Number: TPS23751I am starting a new Class 4 PoE design, and I was wondering if anybody has experience on which part has better EMI/EMC performance, the TPS23751 or the TPS23754?  I can give up...

View Article

Image may be NSFW.
Clik here to view.

TPS54116-Q1: Compensation network calculation

Part Number: TPS54116-Q1Hi team,Since there is a buck converter inside TPS54116, do you have a tool like this to help design the compensation network more quickly? Thank you very much for your help.

View Article

LM76003-Q1: 9-36V input, 12V output, when the input is lower than 12V, how...

Part Number: LM76003-Q1Dear team,The input voltage is 9V-36V, and the nominal voltage is 24V. The expected output is 12V. When the input is lower than 12V, in my understanding the high side mosfet will...

View Article
Browsing all 35901 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>