Quantcast
Channel: Power management forum - Recent Threads
Browsing all 35901 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

TPS65400EVM-678: i2c connection

Part Number:TPS65400EVM-678we have got one evm board, we were not able to communicate with it using USBANY EXPLORER although we followed the user manual.I have starting developing the FW to communicate...

View Article


Image may be NSFW.
Clik here to view.

UCC28780: UCC28780 powered on with very light load

Part Number:UCC28780Hi,I use UCC28780 to design a 5Vout design, and I face the issue at light load.1. When power on the board with 0A load, the output voltage is not regulated to 5Vout, varies between...

View Article


TPS7A45: TPS7A4501 Question About Overshoot at power up

Part Number:TPS7A45Dear support member,My customer made board of TPS7A4501.Overshoot at power up was became.I have a question.Q1My customer measured overshoot of about 0.4 V.Is it reasonable?Q2Is there...

View Article

LM5026: LM5026 Current limit

Part Number:LM5026Hi team,I have 2 questions about current limit of LM5026.1. The datasheet mentioned the current limit will active If the sensed voltage at the CS comparator exceeds 0.5 V, the present...

View Article

TPS7H3301-SP: Aging degradation effect

Part Number:TPS7H3301-SPHello,This is related to the aging question that was previously posted for this component. I'm carrying out an EOL analysis on this VTT regulator, but a longer mission scenario....

View Article


TPS2546: TPS2546 can not charge to IPHONEX when phone's screen was locked

Part Number:TPS2546Hi Team:We configured TPS2546 as CDP in notebook system, when plug IphoneX into this charging port, notice that Iphone X can’t be charged if phone's screen was locked, while can be...

View Article

LM3488: The output presicion

Part Number:LM3488Hi,The input voltage is 5V, and the output voltage is from 0V to 300V/5mA. I want to use MCU to control the output voltage which varies from 0V to 300V.My question is: what the output...

View Article

UCD9090A: How to set up power off

Part Number:UCD9090ADear Team,Is UCD9090A can support GPI to do the power off sequence?Customer wants to use GPI to monitor few rail trigger the power off.BRKevin

View Article


BQ24630: Charging NMC batteries with BQ24630 (Lithium Nickel Manganese Cobalt...

Part Number:BQ24630I am working with the BQ24630 for a LifePo4 charger, but want to charge the latest version of Lithium cells now, NMC.Differences between LifePo4 and NMC:LifePo4:nominal voltage:...

View Article


TPS74801: Bode plot measurement

Part Number:TPS74801Hi team,For TPS74801 or general LDO product, is bode plot measurement needed to make sure the stability?If yes, how can we fine tune TPS74801 if the gain/phase margin is not...

View Article

BQ40Z50-R1: reprogramming bq40z50-R1

Part Number:BQ40Z50-R1I am having some difficulty reprogramming the bq40z50-R1 using bqStudio 1.3.54.1.  When I attempt to download a .gg.csv file from my data storage andwrite it to the data flash, it...

View Article

Image may be NSFW.
Clik here to view.

BQ24780SEVM-583: Learn mode

Part Number:BQ24780SEVM-583Hi expert, I connect Vsys to a CC mode E-load and connect Vbat to a power source. When I enable the learn mode by  battery management studio. The Vsys is still equal to...

View Article

TPS2660: Device shuts down output power when a computer is connected

Part Number:TPS2660I am using TPS2660 for distributing power to a couple of devices. The peak current requirements are within the 2A limit set by R(ilim).I am able to power some of my other circuit...

View Article


BQ24400: NRND: what do we advise for new design?

Part Number:BQ24400Team,What active device would be the closer to BQ24400 in term of specification?Thanks!Anthony

View Article

Image may be NSFW.
Clik here to view.

TPS54202: The PWM waveform at SW feet will wobble

Part Number:TPS54202Using the following circuit, Vin=20V and Vout= 3.6V.Load plus 0.5A, but the PWM waveform jitter in SW foot, how to solve?

View Article


BQ40Z50-R1: User Memory Block?

Part Number:BQ40Z50-R1Is there any way for the user to save a small block of data in flash (<1k)?  If no, is there a similar gauge that has this capability?

View Article

BQ24725A: Why won't the device reset with no adaptor connected?

Part Number:BQ24725AHi,in the datasheet it says the device will reset if ACDET<0.6v, since ACDET is from adaptor, if no adaptor is connected, ACDET should be 0 and the device can't work.Where am I...

View Article


LMR14006: Inverting output

Part Number:LMR14006Hi,Has anyone tried to use the LMR14006 as a inverting converter? From my understanding, the LMR14006 could be used as the TPS54060 to get an negative output. I want to design a...

View Article

BQ24261: Recovery from ESD Event

Part Number:BQ24261ESD testing causes device to stop charging. Charge current drops from ~400 mA to ~100 mA and charger status reads "READY".  Can read battery voltage before and after ESD event over...

View Article

BQ3050: bq3050 BootROM mode and .senc file

Part Number:BQ3050Hi,I wanted to access the .senc file for bq3050. Therefore, I used the bootROM mode (0x0f00 command) in order to download the .senc file.Following that I loose communication access to...

View Article
Browsing all 35901 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>