Quantcast
Channel: Power management forum - Recent Threads
Viewing all 35901 articles
Browse latest View live

TINA/Spice/TPS7B8250EVM: TPS7B8250 for Automotive

$
0
0

Part Number:TPS7B8250EVM

Tool/software:TINA-TI or Spice Models

Hi, could you let me know has TPS7B8250-Q1 and TPS7B6850 been used for Automotive?

please also let us know which application?


BQ24073: BQ24073 charge wave abnormal

$
0
0

Part Number:BQ24073

sir,

customer test BQ24073 charge voltage /current wave as below , what's reason will  happen charge current will drop down 2s, there are two times happen it during total charge stage. R713 is resister between TMR and system, now is 68k, if they change R713 to 100k, drop down times will change to 1 time,  pls refer the second picture, customer want to know why will happen drop down current or voltage like below picture.

R713 Change to 100k.

TLV713P: very light load operation

$
0
0

Part Number:TLV713P

Hello,

I think TLV713P is cap free LDO. Is TLV713P stable even though very light load condition? I assume load is TMP102 which supply current is around 10uA.

Best regards,

Toshihiro Watanabe

LM5175: If LM5175's Mode pin could be floating ?

$
0
0

Part Number:LM5175

Hello

My application have risk of causing Mode PIN floating ,so what LM5175 will hapen ? my application will be ok? 

TPS51206: Power off sequence of TPS51206

$
0
0

Part Number:TPS51206

Hi

I have a question about power off sequence if TPS51206.
The power off sequence is recommended VDD, S3 and S5 are first, next VLDOIN and VDDQSNS  in "7.3.6 Power On and Off Sequence".
But VDD is power off at last in figure 23.
Which is correct?

Best regards,
Yokota

TPS7A49: TPS7A49 current drift under high temp test

$
0
0

Part Number:TPS7A49

Hi,

i'm in midst of running some high temp test on TPS7A4901DGN with regulator step down from 12V to 9.3V.

Recently we found thermal issue on this device, my initial suspect that this issue was caused by output current consumption. The measured worst case current consumption was 152mA which exceeded the max current of 150mA. According to datasheet section 8.4 on operating modes, my device should still be functioning since it's still below the Ilim of 220mA since Iout<Ilim condition is still in place. if that's the case what will be the potential risks i may face & any recommended guidelines to follow? Thanks.

Regards,

Leo

TPS51367: Not found the EVM

$
0
0

Part Number:TPS51367

Hello,

I'm not able to find the TPS51367 EVM on the web.
Is there any way to get something of evaluation kit when we'd like to evaluate it?

Regards,
Shinya Sawamoto

TPS23861: PSE connect to PSE

$
0
0

Part Number:TPS23861

Hello

      if customer use TPS23861 that PSE connect to another PSE via cable. Has any damage risk for it? Has any protection integrated on TPS23861? Thank you. 

BR

Patrick


BQ76930: Schematic review for 8 cells

$
0
0

Part Number:BQ76930

Dear Sir/Ms.

My customer want to design a BQ76930 but they have some questions.

1. Can the BQ76930' current detection part be measured at high side? Did BQ76930 support high side sense?
2. Does the BQ76930 achieve Pre-Discharging Solution without using GATE DRIVE IC (BQ76200)?
3. If you really need GATE DRIVE IC to achieve Pre-Discharging function, then can the BQ76200 be placed on the low voltage side? Is there any other solution? Because my customer must have MOSFET and current detection The parts are placed on the same side so that I can reduce one of the lock terminals.

Best Regards,

Kami Huang

BQ25895: software/ how to test/ 2 input

$
0
0

Part Number:BQ25895

Hi team,

customer would like to use BQ25895. they have 2 input, one is adapter another is solar board.

need your help for below,

1, will we provide Algorithm? where can dowload?

2. how to do the testing to verify the solar charge?

3. they have 2 input, one is adapter another is solar board. when only solar input and the current lower than the system current, how will it work? will it keep switching between battery and solar input?

Compiler/USB-TO-GPIO: Adapter not attached

$
0
0

Part Number:USB-TO-GPIO

Tool/software: TI C/C++ Compiler

I have connected the device to the system. The green LED glows. But I get adapter not connected error.

TPS92515: Repeatable Error After Power Cycle

$
0
0

Part Number:TPS92515

Hi Irwin :

I also encounter "self calibration of the TPS92515" issue. Could you give me more detailed documentation?

Best regards

Janson

TPS23880: The work of TPS23880

battery hot swap solution

$
0
0

Hi TI,

       Our  customer need one battery hot swap,sub battery will be  used when the main battery is removed ,could you recommend one solution?

thanks

Peiyuanqing

TPS7A05: Abnormal Ignd issue

$
0
0

Part Number:TPS7A05

Hello, 

My customer find the Ignd of TPS7A0533 is quite big.

Test condition:

The circuit is powered up by 3.6V battery, VCC is connected to load, FB1 is left disconnected, the current meter is in series in input end.

Load=600K, measured current is 206uA, then connect battery to VCC directly(R52 disconnected), I=6uA, Ignd=200uA.

Load=2K, same test approach, Ignd=260uA.

It seems that the Ignd is much more than the nominal spec.

The schematic is as below for reference.


BQ40Z50-r1 0x54 OperationStatus register and ManufacturerAccess() 0x0054 OperationStatus register difference,tks!

$
0
0

Hi,

  two questions ask:

 1. About OperationStatus register ,from the BQ40Z50-r1 Technical Reference,i knwon that,it has two way to access,one is used   0x54 register  ,another way is ManufacturerBlockAccess() or ManufacturerData(),

      These two way can read the same results?

2.How to read ManufacturerAccess() 0x0054 OperationStatus register? is the same as below? First write command 0x00,data sent 0x0054,then read command 0x23?

Thanks!

why can not Enter the shutdown mode?(BQ20Z75)

$
0
0

Hi,

      why  Manufacturer Access enter 0010,device can not  Enter the shutdown mode? Thanks!

LM5175: Unstable

$
0
0

Part Number:LM5175

I have a similar problem.

What has been the final solution?

Best regards.

TPS7A69-Q1: PG left floating when not used

$
0
0

Part Number:TPS7A69-Q1

Team,

I'm using the TPS7A6950-Q1 and don't need the PG function.

Can I let the pin floating in this case or are there any concerns?

Thanks and best regards,

B

BQ25505: BQ25505 input/output graph

Viewing all 35901 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>