SLUA962
Messrs TI,following your application note SLUA962, in order to avoid to damaging the converter because of reverse current, is it possible to choice a synchronous DC/DC converter with a...
View ArticleLM5022: Does LM5022 has OCP and skip or hiccup mode？
Part Number: LM5022Hi Team,Does LM5022 have OCP? How about the stability under very light load, does it have skip or hiccup mode？Thank you!Marc
View ArticleLM5180: isolation and transformer recommendation
Part Number: LM5180Hello team,my customer needs an AC/DC flyback with roughly an input from 18Vac to 30Vac and 5W. We've noticed that in our app notes we always indicate the use of transformers,...
View ArticleTPS62810-Q1: Cff selection, TPS62810-Q1 EVM circuit suggest 22pf but the...
Part Number: TPS62810-Q1Hi For Cff selection TPS62810-Q1 EVM circuit suggest 22pf but the datasheet suggest 10pF which one should we follow ? and theory behind ? (is there any application note...
View ArticleTPS62810-Q1: input capacitor selection
Part Number: TPS62810-Q1Hi the datasheet suggest 22uF is good enough. However the TPS62810-Q1 EVM use 100uF + 22uF + 10uF + 2.2uF + 470pF for the input capacitor. May i know why EVM use 5 pcs of...
View ArticleBQ76940: How to Insert Own Code to BQ76940
Part Number: BQ76940Hello,I want to develop and try my own battery management system algorithms. Thus, I need to code the chip on my own. I want to learn if that is possible; if so , how?Thanks.
View ArticleHigh voltage, High current multi-phase buck controller
Dear,I'm looking for a current controller that can handle a output voltage of 150Vdc and output currents of 300A, minimum of 6 phases such that each phase gets 50A.The input is 230VAC, hopefully I can...
View ArticleClik here to view.
LMR16030: Output spike at hot swap from 24v battery connector.
Part Number: LMR16030Hi , Customer's product is using in truck the supply voltage is 24v from battery. At car production line when they assemble the board it's high probability to damage the PMIC...
View ArticleWEBENCH® Tools/TPS54360B: Webench not in line with data sheet?
Part Number: TPS54360BTool/software: WEBENCH® Design ToolsHello Team,it looks like I get different results between data sheet and Webench when calculating the compensation with these...
View ArticleTPS61096A: operating at -55°C?
Part Number: TPS61096AHello,For a new design, the reference TPS61096A matchs all our requirements except the negative temperature.On the datasheet, the minimun operating is at -40°C. Our design...
View ArticleEM1402EVM: EM1402EVM
Part Number: EM1402EVMHi, I have some questions about EM1402EVM. 1) In the EM1402EVM datasheet shows an image were the external power supply is 12V/24V but then it says that the positive external...
View ArticleBQ40Z50-R2: What caution for soldering battery on the PCB?
Part Number: BQ40Z50-R2Hello,The BQ40Z50-R2 is used on a battery pack 3S-1P 3.6Vx3 3500mA (prototype phase).When the battery pack is soldered on the PCB supporting the BQ40Z50-R2, the BQ40Z50-R2 is...
View ArticleBQ76PL536A-Q1: Functional Safety IEC60730 Certification
Part Number: BQ76PL536A-Q1Hello,I was advised by customer support to post the query here. We are trying to get a Li-Ion safety system using the BQ76PL536A-Q1 through certification for IEC60730.The...
View ArticleClik here to view.
TPS63030: TPS63030 extreme current draw from EN pin (>50ma)
Part Number: TPS63030Hello, i have the following circuitwhich is pretty much a copy of the one in the datasheet, with a small difference, the enable line is externally driven, in this case an...
View ArticleBQ4050: Syntax for reading/writing to registers
Part Number: BQ4050Hi,My customer would like some help understanding how to read and write to the registers.For example: to read the AB register-SMB sequence:*** Write first to BQ4050 to setup internal...
View ArticleLM5160: LM5160 Adjust On-Time During Operation
Part Number: LM5160Hi Team,we are considering adjusting the On-Time defined by RON during operation to optimize the resulting switching frequency.Our load is very, very slow, so we could use a µC to do...
View ArticleTPS659037: LDO1 voltage value
Part Number: TPS659037Team, please help answer question from my customer:I notice that the voltage of TPS6590379 LDO1 is ~3.00V, not ~3.30V as advertised. Is this correct?I am using the 9ZWS version,...
View ArticleBQ24074: OUT pin driven to 5v
Part Number: BQ24074I have a question presented about the BQ24074 in a current design. The OUT pin is a regulated voltage, but the customer requests that they have the capability to drive the node to...
View ArticleLM2588: LM2588 Oscillations
Part Number: LM2588I have a question on an issue I am seeing here. We’ve been using this part on a flyback for quite a while now (on the order of 5 to 10 years) and we have had a rash of failures...
View ArticleLMG1020: LMG1020 in High Side mode?
Part Number: LMG1020Hello,My name is Serguei Dorofeev. I would like to build a highest speed Half-Bridge GaN FET driver. I would like to use LMG1020 on high side also to get maximum speed from this...
View Article