Quantcast
Channel: Power management forum - Recent Threads
Viewing all 35901 articles
Browse latest View live

TPS92610-Q1: May we know if TPS9261x-Q1 parts can pass EN50155/EN50121 certification?

$
0
0

Part Number: TPS92610-Q1

Hi Sir 

May we know if TPS9261x-Q1 parts can pass EN50155/EN50121 certification?

                                                     Bogey


TPS3710: Power management forum

$
0
0

Part Number: TPS3710

Hi Team,

Please kindly help me to suggest if we have any simple RESET IC that has following spec. Thansk a lot!!

1) Tpd <18uS typ

2) adjustable threshold voltage

3) Prefer open drain 

4) No need programmable delay time

5) Don't care active LOW/HIGH

6) No need Watchdog

Andrew

TPS23754EVM-383: TPS23754

$
0
0

Part Number: TPS23754EVM-383

Hi There , 

I am using this solution to provide 12V for my HMI system .

In the EVM schematic , the GND of  RJ45 connector is independent , should I connect it to system GND ?

Do you have any suggestion for that ?

Thanks 

Tony

TPS23754EVM-383: TPS23754

$
0
0

Part Number: TPS23754EVM-383

Hi There , 

I am using this solution to provide 12V for my HMI system .

In the EVM schematic , the GND of  RJ45 connector is independent , should I connect it to system GND ?

Do you have any suggestion for that ?

Thanks 

Tony

Looking for Bi-direction hot swap for battery...

$
0
0

Dear Sirs,

My customer need bi-direction hot swap in battery trail!

Due to battery need be power source and can be charge, bi-direction is need.

The Battery voltage is 12.6V and the current need 5A.

Please help to suggest solution for it.

Thanks.

TPS65381A-Q1: Can this device work with 5V input supply?

$
0
0

Part Number: TPS65381A-Q1

Hi team,

My customer want to use TPS65381A-Q1 to power TMS570, however their system can only provide 5V supply. I wondered can this PMIC operated with 5V input? Is there any reference design for 5V operation?

Thank you,

John

UCC21732-Q1: Undervoltage and Desat fault false triggers

$
0
0

Part Number: UCC21732-Q1

Hello TI Team,

We have a new project for passenger vehicle motor drive, where we tried to simplify our existing gate driver design using UCC21732. We built board and are using it on FF600R12ME4C module (half bridge) just for testing.

Three boards combined spins the motor just fine for now (not fully tested) except for occasional UVLO and desat trips.


We narrowed down problem where we can reliably reproduce it. SCH below:

PS voltage is +16V, -4.7V. On the PWM input is Rigol DG1022 signal generator. We can switch HS or LS or both IGBTs, same problem.

Scope screenshot:

 

CH1 yellow: PWM input
CH2 blue: IGBT Gate (differential probe between E and G)

With narrow pulse, approx. 300ns wide, UVLO fault happens. IGBT is turned off after 5us just like datasheet says (VDD UVLO off delay to output low). IGBT turns back on after 0.8ms, as per DS.

If we decrease pulse width even further we get desat fault. UVLO and desat faults happens only with high duty cycles (>99.4% @20kHz). We could not reproduce problem with low duty cycles (when signal goes high for short time).

Short circuit between E and C to bypass desat - no change. Short circuit between pins 2-3 - no change.

PWM frequency also doesn't matter, only pulse width.

Zoomed in pic:

CH1 yellow: PWM input
CH2 blue: IGBT Gate

It looks like it happens when IGBT doesn't have enough time to fully turn off. Gate voltage manages to go down only to 4V.

PS voltages two pics below:

CH1 yellow: Voltage between driver pins 3 and 5 (COM and VDD)
CH2 blue: IGBT Gate

CH1 yellow: Voltage between driver pins 3 and 8 (COM and VEE)
CH2 blue: IGBT Gate

PS voltages looks stable enough with sufficient margin to not trip UVLO levels.

We could reproduce the same problem with 10nF foil cap on gate, instead of IGBT, with pulses less than 200ns, so some of my colleagues expressed worries that noise on short pulses could be source of the issues.

So we removed IGBT and put 10uF cap on the gate. This should be slow enough to eliminate short pulses theory. We needed to modify PS (put a LOT of caps) for this to work. PWM frequency is set to 100Hz. Desat sense is shorted.

Normal operation (PWM pulse width >18us):

CH1 yellow: PWM input
CH2 blue: 10uF Cap (diff probe close to gate resistors)

Fault (PWM pulse width <= 18us):

CH1 yellow: PWM input
CH2 blue: 10uF Cap

UVLO fault triggers when gate voltage could not fall below 4V. If we decrease pulse width even further desat fault latches output to -4.7V.

We can provide more details if needed, please advise.


Kind regards,
Zoran Halić

BQ24253: Battery Charger

$
0
0

Part Number: BQ24253

Hi Team,

I would like to evaluate charger + fuel gauge from TI.

In my application I looking for charger with D+/D- so I found BQ24253.

I found that TI doesn't have EVM for BQ24253 only for BQ24251EVM-150, can I use it? is it same die as BQ24253? Does TI recommended this part or other part?

General question – how the D+/D- detection works? It can detect any USB from PC?

I would like to understand how D+/D- detection feature works.

Here are my questions:

  1. Who is detected between PC USB and charger? Is the PC USB asking which charger is connected or the opposite?
  2. Who decides how much current will use for the charging? Is it the PC USB based on the handshake with the device?
  3. If the power source is wall adaptor (connecting to the same USB port on the device) , which current will use for charging?

 

If there is an application note that describe the handshaking flow it will be excellent.

 

Thanks,

Shlomi

 

 


BQ51050B: BQ51050B: Charging not happening when the distance between receiver coil and wireless charger transmitter pad is zero (Receiver module placed directly above charger pad)

$
0
0

Part Number: BQ51050B

Hi,

We are facing an issue with a module having wireless charger and receiver IC BQ51050B. The issue is, when we are placing the receiver module directly above the charge transmitter pad charging is not happening. But when we are slowly keeping the receiver module above the charge transmitter pad with an air gap of around 3mm, charging is initiating and we can put the receiver module freely above the charge transmitter pad, the Battery will charge (sometimes charging stops before full charge and then we have to take the receiver module from the pad and place it again like explained above). What may be the reason for this?.  What we have tried is we have placed a thermocol of thickness more than 3mm and placed the receiver module above the thermocol. Irrespective of how many times and different directions we tried, the Battery is charging suddenly; without any interruption Battery is fully charging. Receiver coil self inductance (Ls) is around 28uH and Ls' with Ferrite sheet, Battery and primary shielding is around 32uH.

Expecting support as soon as possible.

Regards

Hafiz

TPS63030: Inductor size reduction

$
0
0

Part Number: TPS63030

Hi Team,

Would you advise the smaller size recommend inductor than described in the datasheet which

are all 3 mm x 3mm size.

Conditions are : Vin =3V to 4.35V, Vout=5V, Iout=500mA, OSC=default(2400KHz)

Any advice should be highly appreciated.

Thanks

Best regards,

Shidara

UCC28742: UCC28742

$
0
0

Part Number: UCC28742

Hi,

I am using UCC28742 to drive an external mos. To test it individually, I have applied a VDD of 25V, CS 4V and VS of 4V. But there is no pulse at the DRV pin. Kindly suggest

Regards,

Pruthvi

CSD25402Q3A: battery FET

$
0
0

Part Number: CSD25402Q3A

Hello

  1. Can we interpret it as while this MOS was used as a battery FET, we can  ignore the avalanche ?

 

  1. For the diode forward current, as below, VF=0.525V at the Max Current occur, and cause the system is just going to start, we can take the Temp. as room Temp.(25C)

So the PD = 0.525V * 40.4A = 21.21W < 69W, am I correct?

BR

Patrick

LM3478: About ripple voltage at light load.

$
0
0

Part Number: LM3478

Hi team.

Please tell me how to reduce the ripple voltage at Burst Mode(light load).

Sincerely.

Kengo.

Open protection of UCC28180

$
0
0

We have question about UCC28180.

The output voltage of PFC is directly applied to VSENSE pin if RFB2(R13) in datasheet p.22 Figure 29 is open.

Is this understanding correct?

Is there the resistor  in VSENSE pin for protection function when voltage detection resistor is open?

Best regards,

Takahiro Nishizawa

BQ24157: Vbat voltage is unstable

$
0
0

Part Number: BQ24157

When the battery is discharged to the automatic shutdown (the software is set to 3.4V shutdown), the measured Vbat voltage is about 3.3, and it is rested for 1-2 days. Then the Vbat voltage is measured. It is found that the voltage drops to 2.9v or 3.1v, and then the USB is inserted to charge. It is found that there is a probabilistic charging failure (about 0.009A).

The experimental measurements were made: unplug the battery, insert the usb, test the Vbat voltage only 3.54v (Please visit the site to view this file)


LM5118: Simulation Error while Simulating LM5118 unencrypted model in Simetrix 8.3

$
0
0

Part Number: LM5118

Hi , 

    I am using LM5118 for realizing Buck-boost Converter. The design is such that the Input Voltage (6V-26V) to Output Voltage (15.5V) with full load current of 2.25A. I am simulating the same in Simetrix using LM5118 unencrypted model, but it shows the following error. 

There are errors in the circuit. Simulation aborted

design.net (107): Ren2gnd EN GND 1/gmin

*** ERROR *** Cannot evaluate '1/gmin'

Need help regarding this.

 Thanks & Regards

Athieshkumar T

TPS40170EVM-597: Low noise operation

$
0
0

Part Number: TPS40170EVM-597

Hello,

We are developing a low noise output DC-DC converter using the TPS40170 and have developed a prototype based on the TPS40170EVM-597.

We have achieved low noise (less than 5 mV pp) by post filtering the switching ripple and noise, frequency locking to a crystal based external oscillator and providing a low noise external reference.

The dominant noise now has a 1/f characteristic with frequency components less than 15 kHz.

We believe the dominant noise source is now the input noise of the TPS40170 internal error amplifier.

Can you provide any data on the input noise of the TPS40170 internal error amplifier?

Can you please advise on the effect of bypassing the internal error amplifier and of driving the COMP pin from a low impedance output external error amplifier might be?

If the error amplifier inverting input is left floating can we force the output of the amplifier (the COMP) pin using an external error amplifier?

Do you have any noise data or recommendations for low noise operation for the TPS40170 oscillator and TPS40170 PWM comparator ?

Do you have any recommendations for an alternative DC-DC controller to realise a low noise output.

Our requirement is 24 V DC in to 5 V / 8 A out and  24 V DC in to 12 V / 2 A out

Regards

Peter Sykes

 

BQ40Z50-R2: I2C communication

$
0
0

Part Number: BQ40Z50-R2

Hello sir, 

I am writing code for communication between gauge(bq40z50R2) and STM32L476RC by using STM32CubeMX for getting data(V,I,T) in STM32 Controller.I successfully generated code after confugering stm32 pin for I2C. But dont know what should i write in main program.So,if you have sample code for stm32 cubemx,please share it.

Thanks

Mohan 

TPS65150: Minnimum voltage of undervoltage lockout threshold(VIN)

$
0
0

Part Number: TPS65150

Hello

My customer want to check the value of Minnimum voltage of undervoltage lockout threshold(VIN)? datasheet just have typ and max value,thanks

TPS54335AEVM-010: Phase Margin is too low issue.

$
0
0

Part Number: TPS54335AEVM-010

Hi Expert,

If I used EVM Comp value to Webench, the Webench will show the error message. Which one is correct? Thanks!

Viewing all 35901 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>