Part Number: TLV62568
Dear all :
I have a requirement: 5V input, 1.2~2V output, 100mA.I need the output to be controlled by the MCU
Question 1: can FB foot of TLV62568 control the output change by accessing MCU?If so, how to connect?How should the output voltage be calculated?
Question2: if not, is there any other recommended solution?
Hi Sir,
Please help check if any replacement for APL5317-12, thank you.
Best regards,
Part Number: BQ25713
Hi,
Please let me ask about accuracy of Ichg setting. Is the min/max value guaranteed with tolerance of 10mohm Rsns? Then what tolerance do you expected, 0.5% or 1.0% like WSLP series from Vishay used in EVM?
Best Regards,
Satoshi
Part Number: BQ24157
Dear all,
I would like to ask a question.
According to the following table in datasheet p.27,
If Bit B2 to B7 are 1, the charging voltage will be 4.8V, exceeding the maximum charging voltage (4.44V) of this device.
In this case, the charging voltage is 4.44V, which is considered not to exceed the maximum value. Is it correct?
Best Regards,
Y.Ottey
Part Number: LM5026
Hi Sir,
Can you kindly share 50W adapter reference design for our reference?
Thank you.
Johnny
Part Number: MC33063A
Hi Sir
May we have more high current(2~3A) and P2P MC33063A solution?
Bogey
Hi Sir,
Please help to check if any replacement for RP111H071D-T1-YE, thank you.
Best regards,
Part Number: TPS82085
Hi team,
Could you tell me how to set the divider resistor for Vo=0.8V?
Because I use WEBENCH simulation result is 1R and 1MR.
But base on datasheet recommends Rbot not higher 180KR.
So do you comment it? Thanks!
Part Number: BQ40Z50
What does this mean?
"Value is beyond maximum value defined for parameter: Calibration.Current.CC Gain"?
What can I do to restore a right value?
Thanks
Part Number: UCC28950
Hi,
With reference to UCC28950 datasheet, as per block diagram on page number 16, pins OUTB, OUTD, OUTF seems to be active low.
However, as per the OUT pin description table, there is no clear information about the default logic of these pins. Would need verification if these pins were active high or low. Thanks.
Regards,
Leo
Part Number: BQ24650
hello,
i am trying to charge 2s2p lipo 1200mAh batteries from solar panels using BQ24650. the input voltage from the solar panels is around 4.4v.
1. would it be a good idea to use a diode in series to increase the input voltage to atleast 5v?
2. can the bq24650 boost the voltage or will i have to configure it as sepic?
thank you!
Part Number: UCC28251
HI, got confused, what is pre bias and pre biased start up with respect to UCC28251.
Part Number: TPS23880
Tool/software: WEBENCH® Design Tools
Hi TI Team,
We also checked the TPS23880EVM document. In page 2 of that document, it says:
“Two IEEE802.3bt (draft) 4-pair ports with 1000BASE-T (gigabit Ethernet data pass-through)”
That means that the EVM supports only 1Gb Ethernet.
Do you have similar or higher version of PoE EVM (Evaluation Module) that design to run in 10GbE?
In case none, do you plan to create one? Or can you recommend TI third party partner that has EVM that support 10GbE?
Appreciate immediate response.
Thanks,
Conrad
Part Number: TPS23880
Hi TI Team,
We also checked the TPS23880EVM document. In page 2 of that document, it says:
“Two IEEE802.3bt (draft) 4-pair ports with 1000BASE-T (gigabit Ethernet data pass-through)”
That means that the EVM supports only 1Gb Ethernet.
Do you have similar or higher version of PoE EVM (Evaluation Module) that design to run in 10GbE?
In case none, do you plan to create one? Or can you recommend TI third party partner that has EVM that support 10GbE?
Appreciate immediate response.
Regards,
Cons
Part Number: TPS40210
Hi,
Switching frequency depends on VDD on customer's circuit.
At VDD=12V, it is 86kHz, at VDD=30V, it is 84kHz.
Is this variation valid?
The RC pin is connected with VDD via a resistor on the schematic.
RT=680kHz, CT=220pF
Best Regards,
Kuramochi
Part Number: TPS22810
Reading the datasheet of the part, I see that you recommend a 10:1 ratio for input:output (Cin:CL) capacitance. Why then are the scope shots showing curves for 1:10 vs 1:22 ratios? It is highly confusing.
Part Number: TPS61193-Q1
Is there a time limitation that the device will be no problem if voltage ramps up beyond the absolute maximum ratings?
-4.0V, 40ns is assumed in worst case.
Does it cause permanent damage to the device even 40ns?
Part Number: LM5163-Q1
We are developing an automotive grade BMS. For that we need help with our design to make it comply with EMI EMC guidelines. Can you please share the mail id i need to review the ckt and Gerber file,...
Part Number: BQ25703AEVM-732
Hi,
Why there is 150pF capacitors added between gate and source of Q2 and Q3? Is it recommended to add those caps in design no matter what?
Rgds,
Juha
Part Number: TPS61194-Q1
Hi ,
I am connecting TPS61194-Q1 PWM pin to a MCU , in that at when PWM pin is pulled ground ( continuous zero ) the screen turn blank , Can I or the PWM signal with Vref ~1.2V & then give to PWM pin so when the PWM from the MCU is pulled zero , VREF appears at PWM pin . Is this acceptable , because as per internal block diagram of IC it needs PWM to control brightness .
Please guide me. I basically need a min brightness , the screen should not turn blank.
Gaurav